Appletalk problems with dual nic

judge

Registered
Hey all,

Curious if anyone else has experienced this or if someone can confirm.

My setup is such:

Single G4 with 2 NICs running NAT. en0 [onboard] NIC has external IP, en1 NIC is IP'd to 192.168.1.1

Single IMAC connected to en1, can access internet fine via NAT *and* can access appletalk share on G4 no problem.

Problem:

G4 cannot access appletalk share on iMac, is this a problem with NAT and/or Dual NICs? Anyone else have the same problem?

judge
 
I have not been able to get dual NICs working at all. Can you point me to any resources that might offer help doing this?

Thanks
 
Originally posted by scruffy
I have not been able to get dual NICs working at all. Can you point me to any resources that might offer help doing this?

Thanks

do an:

ifconfig -a

and post the results
 
Unfortunately, it doesn't recognize the card at all.

<tt>lo0: flags=8049&lt;UP,LOOPBACK,RUNNING,MULTICAST&gt; mtu 16384
inet 127.0.0.1 netmask 0xff000000
en0: flags=8863<UP,BROADCAST,b6,RUNNING,SIMPLEX,MULTICAST&gt; mtu 1500
inet 10.10.131.61 netmask 0xffffff00 broadcast 10.10.131.255
ether 00:50:e4:c0:9c:2e
media: autoselect (10baseT/UTP &lt;half-duplex&gt;) status: active
supported media: none autoselect 10baseT/UTP &lt;half-duplex&gt; 10baseT/UTP &lt;full-duplex&gt; 100baseTX &lt;half-duplex&gt; 100baseTX &lt;full-duplex&gt;</tt>

I suppose this means I just wait and hope that Kingston comes out with an OS X driver for the card before my beard turns grey...

...Stupid smileys. I meant &amp;gt; followed by ) not a winking smiley face...

[Edited by scruffy on 12-16-2000 at 04:33 PM]
 
Originally posted by scruffy
Unfortunately, it doesn't recognize the card at all.

<tt>lo0: flags=8049&lt;UP,LOOPBACK,RUNNING,MULTICAST&gt; mtu 16384
inet 127.0.0.1 netmask 0xff000000
en0: flags=8863<UP,BROADCAST,b6,RUNNING,SIMPLEX,MULTICAST&gt; mtu 1500
inet 10.10.131.61 netmask 0xffffff00 broadcast 10.10.131.255
ether 00:50:e4:c0:9c:2e
media: autoselect (10baseT/UTP &lt;half-duplex&gt;) status: active
supported media: none autoselect 10baseT/UTP &lt;half-duplex&gt; 10baseT/UTP &lt;full-duplex&gt; 100baseTX &lt;half-duplex&gt; 100baseTX &lt;full-duplex&gt;</tt>

I suppose this means I just wait and hope that Kingston comes out with an OS X driver for the card before my beard turns grey...

...Stupid smileys. I meant &amp;gt; followed by ) not a winking smiley face...

[Edited by scruffy on 12-16-2000 at 04:33 PM]

Yea, mine is a kingston kne100tx
 
Was your card automagically recognized, or did you have some fussing and fighting to do? I noticed Kingston only offers driver for the kne100tx for up to OS 9 - unless I'm not looking in the right place.

I have the kne30bt, the driver offerings are the same - up to OS 9 only.
 
Originally posted by scruffy
Was your card automagically recognized, or did you have some fussing and fighting to do? I noticed Kingston only offers driver for the kne100tx for up to OS 9 - unless I'm not looking in the right place.

I have the kne30bt, the driver offerings are the same - up to OS 9 only.

nope, worked automagically. the card is only 30.00 bucks, you ought to buy it!!
 
Back
Top